-40%
2x 5' (60
2x 5' (60
2x 5' (60
2x 5' (60
2x 5' (60

2x 5' (60") White LED Boat Deck Light Waterproof Bow Trailer Fishing Pontoon 12v

€ 8.64

Availability: 50 in stock
  • Brand: Fyre Flys
  • Cut to fit: Yes. Cut between copper dots after every 3rd LED.
  • Return shipping will be paid by: Seller
  • Manufacturer Part Number: Does Not Apply
  • Item must be returned within: 30 Days
  • Condition: New
  • Operating voltage: 12v nom / 14.8v max / 9v min
  • Returns Accepted: Returns Accepted
  • Dimmable: Yes
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Country/Region of Manufacture: United States
  • Power Consumption: 0.24w per LED x 180 = 43.2w total @ 12v, 3.6A
  • lumens/meter: Approx 860 L/M, 2580 total @ 3 meters (10')
  • LED type: 180 pcs 5050 SMD triple emitter 3 chip LEDs
  • LED Color: Super Bright 6000K HID Xenon White

    Description

    Package
    Includes:
    2 Pieces 5'-0" (60") White LED strip lights.
    180 Big & Very Bright 5050 SMD LEDs. 90 LEDs on each strip.
    On a white background.
    Compared to other sellers,
    our LED strips use larger and brighter 5050 SMD LED chips. Be careful and look closely. Some sellers use smaller 3528 LED chips but their photos show the larger 5050 LED chips. 3528 LED chips have a single light emitter built in whereas our 5050 LED chips have
    3 light emitters
    built in.
    Features:
    Size: Each strip is 5 feet long x 3/8 inch x 1/8
    inch (Length x Width x Height)
    Each
    light strip has 90 large
    5050 SMD
    LED light chips
    Each LED chip has 3
    light
    emitters
    180 LED chips x 3 light emitters = 540 light emitters
    Highest quality, brand new, and never used
    Thin & flexible
    Waterproof, heat & vibration resistant
    Adhesive backing, simply peel and stick to the desired location.
    Emits a 180 degree, bright, pure color glow
    Positive and Negative Wire attached on one end
    Can be cut between every 3rd & 4th LED. Cut between copper dots. Leftover strips can be reused. Just trim off clear rubber and solder on new wires to the copper solder pads.
    Low current consumption
    Wires can be connected to any 12v source on the boat.
    Easy to install
    100% satisfaction guarantee
    Some important guidelines for installing LED strips:
    These strips are very flexible. However, you should not bend them at sharp angles or you risk damaging the solder connections that hold the LED chips to the circuit ribbon inside. This type of damage isn't covered under warranty.
    Do not bend the LED strips "against the grain" or along the short edge.
    Make sure the power going to the LED strip is turned off when you charge your boat's battery. LEDs are very sensitive to over-voltage and will burn out instantly if too much voltage is applied. Battery chargers often give a voltage spike when initially connected to the battery. LEDs are safe up to 14.5v.
    Make sure the mounting surface is thoroughly clean. If the LED strips are to be applied to a smooth, painted surface, rough up the surface first for best adhesion. Depending on the mounting surface, you may need to use a stronger adhesive. The most common is 3m double sided body molding tape available at most auto part stores.
    Gallery:
    Can be cut between the copper solder pads as shown below. Solder pads are spaced at every 2 inches. To reuse leftover strip, trim off clear rubber coating over the solder pads and solder on wires.
    Rolls are shipped on a plastic reel, in anti static bag as well as a bubble lined package for safe shipping. LED strip is tested immediately before shipping.
    Example photos:
    Thanks for looking!!! :-)
    © 2006 Fyre Flys™
    All photos are property of Fyre Flys Inc.
    Copying photos is prohibited.